Accucadd Quickstart Tutorial
 

Contents

(On-Line Version)

Click one of the links, below:
Chapter File Name Page
Disclaimer (contents.htm)  ii 
Introduction (intro.pdf)  iii 
Getting Started (start.pdf)  S-1 
Project 1 (proj1.pdf)  1-1 
Project 2 (proj2.pdf)  2-1 
Project 3 (proj3.pdf)  3-1 
Project 4 (proj4.pdf)  4-1 
Project 5 (proj5.pdf)  5-1 
Project 6 (proj6.pdf)  6-1 
Project 7 (proj7.pdf)  7-1 
Project 8 (proj8.pdf)  8-1 
Project 9 (proj9.pdf)  9-1 
Project 10 (proj10.pdf)  10-1 
Project 11 (proj11.pdf)  11-1 
Appendixes    
Colors And Layers (col_lay.pdf)  A-1 
Printing (print.pdf)  B-1 
Start Up Settings (settings.pdf)  C-1 

 
© Copyright 1986-2008 Robo Systems International, Inc.
Accucadd Version First Edition
Issued: August 2001
Editor: C. R. Williams; Associate Editor D. H. Strome
Robo Systems International, PO Box 290, Newtown,  PA  18940-0290


Accucadd — Your Rights and Obligations

Neither the whole or any part of the information contained in, or the product described in, this manual may be adapted or reproduced in any material form except with the prior written approval of Robo Systems International Inc.,  hereafter referred to as Robo.

Robo Systems International
PO Box 290
Newtown, PA 18940-0290
U.S.A
 

Robo products are licensed, not sold. Title to the products remains at all times with Robo. The products, including but not limited to, software and manuals are copyrighted and contain trade secrets of Robo. The licensee agrees to protect the trade secrets of Robo by refraining from unauthorized copying of the product, and by refraining from analyzing or reverse engineering the products.

The product described in this manual is subject to continuous development, change, and improvement.  All information of a technical nature and particulars of the product and its use (including the information and particulars in this manual) are given by Robo in good faith.  Robo welcomes comments and suggestions relating to the product and this manual.

READ THIS — IT IS IMPORTANT AND LIMITS YOUR RIGHTS

This manual is intended only to assist the reader in the use of the product, and therefore Robo shall not be liable for any loss, damage, or injury whatsoever arising from the use of information or particulars in this manual or any incorrect use of the product.

In particular, Robo products are not warranted to be error free. The responsibility for all results of using Robo products rests with the user. In no event shall Robo, its owners, officers, employees, agents, heirs or assigns be responsible or liable for any damages resulting from the use or misuse of Robo products, including but not limited to damages for injury to any person or property, loss of data, lost profits, cost of cover, or other damages which are special, indirect, or consequential. Release from consequential damages may not apply in some states. If for any reason the foregoing provisions shall be ineffective, the user of Robo products agrees that the sole remedy for any claim brought against Robo shall be limited to the amount paid to Robo for the product giving rise to the claim. The licensee, user, and associated parties shall indemnify Robo against and hold Robo harmless from any and all claims brought against Robo based on the use or misuse by any person of Robo products. The licensee acknowledges that the license fee reflects this allocation of risk.

Copyright © ROBO SYSTEMS INTERNATIONAL 2001-2008
Contains material previously copyrighted by Robo

Accucadd, RoboCAD, Sketchpad, RoboSOLID, RoboMILL, RoboUTILITY, RoboFONT, RoboLINK, RoboGUARD, RoboLOG, RoboRAF, RoboSTART, RoboLIB, and RoboDATA, are trademarks, registered trademarks, or service marks of Robo Systems International Inc.